|
|
|
This page explains the software specification of SD-300/SD-310AN.
| Supported protocols | TCP/IP | |
| DHCP, BOOTP, TCP, UDP, ARP, ICMP, IPv4, SNMP, TELNET, HTTP, #3001, #9100, #9200, JCP(silex proprietary protocol), SXSPE(silex proprietary protocol) | ||
| Supported OS |
Windows 2000 SP4 or newer Windows XP SP2 or newer ( 32-Bit Edition / 64-Bit Edition ) Windows Vista SP1 or newer ( 32-Bit Edition / 64-Bit Edition ) Windows Server 2003 SP2 or newer ( 32-Bit Edition / 64-Bit Edition ) Windows Server 2008 SP1 or newer ( 32-Bit Edition / 64-Bit Edition ) Windows 7 ( 32-Bit Edition / 64-Bit Edition ) Windows 8 ( 32-Bit Edition / 64-Bit Edition ) Windows 8.1 ( 32-Bit Edition / 64-Bit Edition ) |
|
| Serial port | Baud rate |
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 (bps) * The baud rate higher than 115200bps is not guaranteed. |
| Bits per character | 7, 8 | |
| Stop bit | 1, 2 | |
| Parity | NONE, ODD, EVEN | |
| Flow control | NONE, XON/XOFF, RTS/CTS | |
|
Wireless LAN (*Wireless model only) |
Authentication method | Open System, WPA-PSK, WPA2-PSK, WPA-EAP(TLS, TTLS, LEAP, PEAP(v0,v1), FAST),WPA2-EAP(TLS, TTLS, LEAP, PEAP(v0,v1), FAST) |
| Encryption mode | WEP(64bit/128bit), AUTO(TKIP/AES), AES | |
| Others | RFC2217 support (see below for details) | |
SD-300/SD-310AN supports RFC2217. When SD-300/SD-310AN is used in Serial Port Emulation Mode, you can utilize the following RFC2217 commands over the network.
| Command | Details | Note |
| SIGNATURE | Exchanges the device information. | Not supported |
| SET-BAUDRATE | Changes the baud rate. | Client -> Server (one-way) |
| SET-DATASIZE | Change the bits per character. | Client -> Server (one-way) |
| SET-PARITY | Changes the parity. | Client -> Server (one-way) |
| SET-STOPSIZE | Changes the stop bit. | Client -> Server (one-way) |
| SET-CONTROL | Enables/Disables the flow control or use for PIN setting. | Client -> Server (one-way) |
| NOTIFY-LINESTATE | Server notifies the client of line status changes. | Server -> Client (one-way) |
| NOTIFY-MODEMSTATE | Server notifies the client of modem status changes. | Server -> Client (one-way) |
| FLOWCONTROL-SUSPEND | The receiver of this command will be unable to send any data or commands. | Client <-> Server (bidirectional) |
| FLOWCONTROL-RESUME | The receiver of this command will be able to send data and commands. | Client <-> Server (bidirectional) |
| SET-LINESTATE-MASK | Set the information to send by NOTIFY-LINESTATE. | Client -> Server (one-way) |
| SET-MODEMSTATE-MASK | Set the information to send by NOTIFY-MODEMSTATE. | Client -> Server (one-way) |
| PURGE-DATA | Requests the server to clear the serial buffer. | Client -> Server (one-way) |
|
|
|
|